Contact US
Address: South Time 16 building 1 Unit Room 1102 Nansha, Guangzhou, Guangdong
TEL: 86-20-28125195
FAX : 86-20-28125195
Home > Exhibition > Content
How to Inject Steroids
- Sep 19, 2017 -

Tips and preparations


Warm your vial as well as ampoule to body's temperature ahead of injection. This can be done simply by positioning that under your equip for approximately a few minutes or perhaps placing the package in hot water.

Right before shot, push the particular plunger to allow a drop of water to make on the suggestion with the needle along with let it movement over the needle. This will likely oil your hook with the gas solution of your respective anabolic steroid.

Organize get rid of your hook (open Versus) towards the torso.

Should you desire, you'll be able to numbing the actual procedure area along with glaciers before continuing.


What needles to use ?


It is important to choose the proper syringe for the administration of injectable anabolic steroids. The main components of a syringe comprises a cylindrical body and a piston to which is fixed a hollow needle. The recommended syringe injections of anabolic steroids is a syringe of size 22 [1 ½ inches] or size 23 [1 inch] with body of 3 cc.


This length allows deep penetration to reach the interior of the muscle tissue. Shorter needles, 5 / 8 or 1 ½ are generally not sufficient for intramuscular injections.

The size number of the syringe represents the diameter of the needle. The smaller the number, the larger the needle. A 27 gauge needle is very thin. A 18 needle is quite wide, it is often referred to as a "canon". Both 22 and 23 sizes are quite thin to be easily inserted, and wide enough to allow solutions to be propelled.

Glute injection: 23 of size 1,5 inch needle length

Thigh Injection: 25 gauge 1 inch of needle length

Deltoid injection: 25 size of 1 inch needle length


Injection procedures

There are a number of steps that must be followed to conduct a safe and proper intramuscular injection. First, 

before handling needles or vials, the user must take a full shower. Then an alcohol swab should be used to clean the injection site and another alcohol swab should be used to clean the rubber stopper on the top of the bottle. Then, take a new syringe, remove the upper part of the plastic, draw approximately 2 ccs of air into it and insert it into the bottle of your anabolic product. Inject this air into the vial, which will create pressure in the bottle and make the drawing of oil-based preparations easier. Then turn the vial head down and slowly pull the oil until you have at least 1 / 4 cc.


For example, if someone were to take an injection of 1 cc, they should draw about 1 1 / 4 css to 1 1 / 2 css of liquid. Then tap on the side of the syringe to help air bubbles that were drawn into the syringe back up. At this time, the excess 1 / 4 to 1 / 2 cc may be injected into the vial and the needle removed.


Then hold the syringe needle-head up and continue to tap to encourage all the air bubbles to come to the top of the syringe. Now exchange the needle with a new one. The needle does not suffer any damage when it is pushed through the rubber plunger on the bottle. It is important not to touch this needle before the injection. It must not come into contact with a counter or your fingers, and it should not be cleaned with alcohol.


This needle is sterile and should not be touched. At this point, once again swab the injection site with alcohol, then press the plunger of the syringe by holding the needle on the side, until the air bubbles completely exit. Once a drizzle of oil appeared at the top of the needle, allow it to flow to the surface of the needle to ensure lubrication.


At this point, take the syringe and hold it like a dart. Use the other hand to stretch the skin over the injection area and then push the needle until it penetrates. After inserting deep enough into the muscle, pull the plunger for a few seconds to make sure it does not fill with blood, which would indicate that the needle was injected into a blood vessel.


If there is no blood in the syringe, slowly press the plunger until all the oil is injected. Then, quickly pull the needle out and take another alcohol swab and press firmly on the injection area. This will minimize bleeding, if any. Pressing down firmly on the injection area and massaging slightly can reduce the pain. It is important that the liquid is not injected too quickly as this causes more pain upon injection and in the days that follow.


Once this step is completed, return the plastic caps to protect the needles and make sure they are properly stored (and then discard or return to your pharmacist). To prevent excessive scar tissue on the injection area, it is not wise to inject more than 2 ccs by solution. It is also not prudent to use the same injection site more than twice a week (once a week is better).